[ad_1]
In yesterday’s publish, I shared Half 1 of find out how to make lined, pinch-pleated curtains. You’ll be able to click on right here to see Half 1 of this tutorial. At this time, I’ll end up that tutorial and present you each element of find out how to end the curtains and hold them. I wish to say up entrance that this publish accommodates an absurd quantity of images (74 to be actual), however please don’t let that intimidate you! This course of isn’t troublesome in any respect, however I wished to incorporate numerous images in order that you might simply perceive each little step of the method. However once more, including pleats and ending up a material panel shouldn’t be troublesome. Simply take it one small step at a time, and also you’ll get it!
Yesterday, I left off with the physique of the material panel completed for essentially the most half, and unfold out on my work desk like this. The hems have been completed, the face material and the liner had been sewn collectively, and I used to be nearly able to sort out the pleated header.
The one factor I nonetheless wanted to do earlier than engaged on the pleated header was to iron within the facet seams to get that actually sharp crease on the facet edges of the panel. I actually took my time with this and didn’t rush this step as a result of these sides should be proper to ensure that the material panel to hold correctly. And once more, that lining wants to increase all the best way to that exterior ironed-in crease alongside the very edge. All the folds are within the material, not on the liner.
With these sides ironed and the panel mendacity flat, face material down and lining up, I measured and marked my completed material size. In case you’ll keep in mind, I had taken this measurement proper on the very starting. You’ll be able to refer again to Half 1 for those who don’t keep in mind.
My completed material panel size was 88 5/8 inches, so I measured and marked both sides of the panel with a pin at that measurement.
For now, I simply did one measurement and one pin on both sides of the panel.
Subsequent, I folded the material over proper at these pins and repinned both sides into place by means of all layers of the material.
After which I measured and pinned the completed top on the remainder of the panel.
I solely wanted to make solely slight changes within the fold as I moved my means throughout the highest of the panel.
As soon as I had the whole high folded to the right measurement and pinned into place, I steam ironed that fold within the high, eliminated the pins, and ironed it once more to ensure I had a really sharp crease.
So at this level, right here’s what the highest of the panel seemed like from the again — no pins and a really sharp ironed-in fold alongside the very high fringe of the panel.
Subsequent, I unfolded the highest and made positive I may see the crease all the best way throughout the panel. (I edited this picture to reinforce the road in order that you might see it. In individual, the ironed-in crease was very simple to see.)
Then I eliminated the stitching holding the face material to the liner from the very high right down to that ironed-in crease.
After which I used that ironed-in crease as a information to chop off the surplus lining. I don’t assume that is 100% vital, however I at all times take away the surplus as a result of it’s going to create two extra layers of material to wrangle into pleats later, and that simply creates pointless bulk that makes pleating tougher than it must be.
Subsequent, I lower my material header tape to size. This can be a thick-ish materials that feels rather a lot like a heavy interfacing. You may get it in numerous widths, however I desire the three-inch width. You should buy it by the yard at locations like Joann Materials.
I lower it to size in order that it spans the width simply contained in the 1-inch facet folds.
Since my header tape is three inches huge, that meant that I wanted to chop away among the extra material on the high. The material wants to increase previous the highest of the lower lining at a measurement equal to 2 instances the header tape width, minus only a smidge. (That’s the technical time period for it. ? ) Since I used to be utilizing three-inch header tape, I lower the material to 6 inches minus a smidge (about 5 7/8 inches) previous the lower fringe of the liner.
So as soon as I had the surplus lower off and it seemed like this, I used to be prepared so as to add the header tape.
I began by inserting the header tape in order that it lined up alongside the highest of the liner…
After which I folded the material down over the header tape alongside the ironed-in crease…
After which beginning within the center and dealing my means out to the ends, I wrapped the surplus material again below the header tape in order that the material enveloped the header tape. After which I pinned all of the layers into place.
And right here’s what it seemed like as soon as it was pinned into place all the best way throughout.
Subsequent, I needed to determine the position of my pleats. The primary measurement I wanted was the return for the surface fringe of the panel. The return is the piece that folds again from the curtain rod and meets the wall. To get this measurement, merely measure from the tiny material pin loop on the curtain ring to the wall. It’s onerous to see from the angle within the picture under, however the measurement from the wall to my curtain rod/rings is 3 1/4 inches.
So I took that measurement and marked off 3 1/4 inches on the outer fringe of the header.
After which I measured and marked off an area on the forefront (the within edge) of the header. I simply went with 2.5 inches as a result of I feel that appears good. However you’ll be able to alter relying on what you assume seems good.
Or for those who’re including trim to the forefront of your material panel (which wanted to be finished a number of steps in the past), you may want to regulate this measurement relying on the width of the trim. The very last thing you need is getting an ornamental trim caught up in your first pleat. Coping with that bulk in a pleat could be a nightmare, and it just about by no means seems proper. Ask me how I do know. ? However anyway, about 2 1/2 to three inches for that vanguard will do.
As soon as I had the return and the forefront marked off, I measured the width remaining between these pins. So I positioned my tape measure proper on a type of pins…
And measured to the opposite one. That gave me a measurement of 43.5 inches. (Once more, the angle on the picture under makes that look a bit off.)
On a single width material panel, I prefer to have seven pleats. And I prefer to have a minimal of three inches of material width to work with per double pleat, or a minimal of three.5 inches per triple pleat. I made a decision to make use of double pleats on these material panels, so I multiplied 7 (pleats) instances 3 (inches per pleat), which meant that I wanted a complete of 21 inches for my pleats. That left me with 22 1/2 inches of material that wanted to be divided by 6 areas between the pleats. (If I’ve seven pleats, I’d have six areas. If I’ve 9 pleats, I’d have eight areas. So the variety of areas is at all times one lower than the variety of pleats.) So 22 1/2 divided by 6 implies that every area wanted to be 3.75 inches huge.
So I used my pins to mark off these areas.
Subsequent I wanted to pin the pleats in order that I may sew them into place. To do that, I folded the material in order that the to pins marking off the pleat met.
I folded the material in order that the again sides have been collectively as proven…
After which I eliminated one of many pins, and pinned all layers along with one pin.
Right here’s what that seemed like pinned in…
Then I skipped the area subsequent to that pleat…
And moved on to the following space marked off as a pleat, and repeated that folding and pinning course of.
So with two pleats pinned in place, that is what it seemed like…
I repeated that each one the best way throughout till I had all seven pleats pinned.
At this level, these different pins alongside the underside of the material header tape/folded material may be eliminated. They’ve served their function properly, however at this level they’ll simply be in the best way.
So with the pleats pinned into place, that is what they appear to be from the entrance. I used my fingers to crease and press the entrance folds into the header tape earlier than I took the panel to the stitching machine.
Stitching the pleats into place is finished with a fundamental straight sew.
To find out the place to stitch, simply divide the pleat material width (once more, mine was three inches) by two, and stitch straight down the header tape from high to backside at that distance. So I sewed my sew at 1 1/2 inches from the sting.
And right here’s what it seems like with the pleat sewn into place.
I repeated that on the opposite pleats, and that is what the header seemed like with all the pleats sewn in.
Right here’s a facet view for a greater look.
These are the essential pleats, however now I needed to kind the “double” a part of the double pleats. To do that, I began my utilizing my finger inside that fold and urgent the seam of the header tape open.
After which I pressed the fold of the pleat down to satisfy the seam…
After which I introduced the 2 sides as much as meet. And that varieties the double pleat.
Pleats may be sewn elsewhere to get completely different seems. For instance, if I sew them into place in direction of the underside of the header tape, it ends in a extra conventional French pleat.
If I sew extra in direction of the highest, it offers a little bit of a extra trendy look. That is known as a Parisian pleat.
I made a decision to go together with extra of a Parisian pleat by stitching the folds collectively about 3/4 inch from the highest, and 1/4 inch from the entrance folds.
Every stitching machine will probably be just a little completely different, however that is what the sew seems like on my stitching machine.
In case you don’t have a sew that appears like that, you should utilize a large zigzag sew with a stationary foot (i.e., set it in order that the foot doesn’t stroll the material ahead).
And right here’s what the sew seems like from the facet.
And right here’s what our double Parisian pleat seems like from the entrance.
After repeating that course of on the opposite six pleats, my header seemed like this…
Solely a few ending touches remained. First, I wanted to sew the very ends of the header closed. I personally do that by hand, and never on a machine.
I’m not the easiest at hand stitching, however I nonetheless assume it seems higher and cleaner than attempting to stitch these layers collectively as near the sting as potential utilizing a machine.
After which I hand sew the very backside corners in order that they keep put. At this level, they have been nonetheless free and never sewn collectively in any respect.
I do that by utilizing the least quantity of hand stitching potential simply because I don’t need it to point out.
So since I used to be utilizing 100% cotton that stays put, I simply put a easy tack sew proper on that internal fold and thru to the entrance material.
That’s not how I discovered to do it in my material workroom coaching, although. So let me present you what I used to be taught is the correct means, simply in case you like it.
First, unfold the nook of the material like this…
Fold the nook up at a 45-degree angle in order that the sting meets that inside ironed-in crease…
After which refold the sting. That offers you a nook that appears like this…
I personally don’t like that. I feel it’s pointless work, creates the necessity for added hand stitching, creates extra bulk. Plus, I simply don’t like the best way it seems. However that’s a private desire. You could desire that means, which after all, is completely high quality. However I personally simply hold mine folded straight, add a tiny little tack sew to maintain the flap of material closed, and go away it at that.
The panel is formally completed! To hold the panel, I had so as to add the material pins to the backs of the pleats. Material pins seems like this…
They’re inserted proper behind every pleat with the hook dealing with down and the sharp level going up. They simply slide proper below the stitches holding these pleats collectively. You’ll get some resistance when placing them in as a result of these stitches must be tight. However for those who’re getting quite a lot of resistance when attempting to place them in, you’re most likely needlessly forcing the pins into layers of material. Simply take away the pin and take a look at once more.
And I additionally added a pin on the sting of the surface return, and about an inch from the forefront…
Then I used to be prepared to hold the panel!
On that return on the outer fringe of the panel, I wanted to place a small eye hook into the wall proper about the place I added the black dot under to be able to connect that final pin to the wall, however I used to be all out of eye hooks. As soon as I get that finished, I’ll add the image right here.
Then I wanted to crease the areas between the pleats in order that they’d keep wright here I wished them. So long as there’s no crease within the areas, that header tape will battle you once you attempt to correctly area your curtain rings.
To do that, I merely introduced two pleats collectively…
After which used my fingers to press in a crease within the header tape on the again.
This can permit the rings to remain the place I need them to remain quite than preventing me as I’m attempting to make changes.
And at this level, the panel was completed and looking out lovely, if I do say so myself! ?
You’ll be able to determine at this level whether or not you need a extra informal look, like what’s proven within the image above, the place the folds within the material look form of carefree and are left to do what they naturally wish to do.
Or in order for you a extra formal, polished, tailor-made look, you’ll must “practice” your pleats and folds. Do that by beginning on the high and patiently folding the material consistent with the pleats. When you get a few foot or two down the panel, use some scrap material to tie the folds into place.
Proceed working your means down till it’s tied in about three or 4 locations and appears like this…
You’ll be able to go away it like that for a day or two, or you’ll be able to velocity up the method by utilizing a garments steamer or steam iron to steam in these folds.
And as soon as these folds are educated, it’ll look extra like this…
I typically don’t like my creases too creased (as they give the impression of being above), so as soon as they’ve had a number of days like that, I’ll typically get my steam iron and hit them with some steam whereas smoothing them out a bit in order that they give the impression of being extra like light waves within the material as a substitute of harsher folds bordering on creases. However you’ll have to find out what your panel wants primarily based in your private style in addition to the material that you just used.
I’m unsure which look I desire but, however I’m leaning in direction of the primary one for my studio. If I determine to go that path, I can simply use my steamer to get these folds out, after which floof the panel like a bridesmaid floofing a bride’s wedding ceremony costume and practice, and that’ll return it again to that extra pure, carefree look.
I hope this tutorial was useful! In case you have ANY questions in regards to the course of, please let me know and I’ll do my easiest to reply.
Addicted 2 Adorning is the place I share my DIY and adorning journey as I transform and embellish the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do nearly all of the work on the home on my own. You’ll be able to study extra about me right here.
[ad_2]
Source link