[ad_1]
Method again once I first began planning the format of the studio, I meant to construct my very own cupboards from scratch. Doing so would enable me to make the cupboards and countertop any top I wished it, so I deliberate to make a typical 30-inch-high countertop, which is a typical top for tabletops and desktops. I designed every little thing to work completely with 30-inch-high counter tops, from the peak of the home windows to the place of the countertop accessible electrical retailers and switches. It was all calculated and positioned with precision to work completely collectively.
Nicely, quick ahead a few years, and after contemplating all the choices, I made a decision to forgo the made-from-scratch cupboards and use IKEA cupboards as a substitute. I preferred the concept as a result of they’d save me a ton of time. However one disadvantage to utilizing IKEA Sektion cupboards as studio/workplace cupboards was that IKEA Sektion cupboards are 30 inches excessive.
These cupboards are meant to be kitchen cupboards, and kitchen counter tops are usually 36 inches excessive. So whenever you buy IKEA cupboards, the cupboard containers themselves are 30 inches excessive, and then you definately’re supposed to buy their cupboard legs that screw onto the underside of the cupboard containers, and then you definately add the countertop of your option to the highest. That usually places the completed countertop at about 36 inches excessive.
Nicely, I didn’t have room for 36-inch-high cupboards since I had designed the room for traditional desktop top (30-inch) counter tops. It’s no huge deal. I don’t have to make use of the IKEA cupboard legs. I could make my very own base and make it the right top that I want to ensure that the countertop to return slightly below the window sills. So whereas that requires a workaround, it’s not an issue.
However the problem I knew I’d face was the retailers and lightweight swap. There are six desktop-height retailers and one desktop-height gentle swap on this wall, and 4 desktop-height retailers on the opposite cupboard wall. With a view to make the taller IKEA cupboards work, I deliberate to maneuver all of these up about three inches in order that they’re above the window sill top.
So earlier this week, I discovered a handyman who mentioned he might do the job (each transfer the retailers after which restore the drywall). He got here early Monday to have a look at the job and provides me an estimate, after which scheduled to return Tuesday morning to do the work.
Nicely, to make a really lengthy story quick, I began having doubts. First, I made a decision that I didn’t like the concept of getting the retailers moved up. I already don’t have an entire lot of wall house on this wall for my mural, and I didn’t like the concept of what little wall house I’ve being cluttered by all of those retailers and a swap. So I made a decision that I wished simply the one gentle swap moved up, however I wished all the retailers moved down beneath desktop top.
After which I began questioning if there was even going to be sufficient wire within the wall to maneuver the retailers in any respect. So I took two of the retailers off to see how a lot additional wire was in there, and because it seems, there wasn’t sufficient wire in any of those retailers to maneuver them up or down.
I tugged on the wires a little bit to see if that they had any slack to them in any respect, and that’s once I remembered that this room has spray foam insulation within the partitions.
It’s the one room in the home that has spray foam insulation within the partitions, and it was sprayed after {the electrical} wires have been run in the entire room. That spray foam actually grabs onto and encapsulates the wires, so there’s actually no strategy to fish wires by means of partitions which might be stuffed with spray foam insulation like you may with inside partitions which might be simply empty house between the drywall.
So after spending strategy to lengthy racking my mind and making an attempt to provide you with any resolution for fishing new wire by means of the froth insulation-filled partitions, I lastly determined that the best resolution could be to take away the drywall from the retailers down, transfer the retailers the place they should go, after which put up new drywall.
With a view to do this, I needed to take away a few of the window casings, however I’m okay with that. It’ll make putting in the brand new mural a lot simpler with out these casings in the way in which, and since all the items got here off simply and intact, reinstalling them can be very easy.
So now with the drywall gone, I’ve full freedom to place retailers wherever I would like them, and as I run the brand new, longer wires between the outlet containers, I can carve out neat, exact little channels within the spray foam insulation in order that it stays intact as a lot as doable. And if wanted, I can fill in any voids with canned spray foam earlier than placing up the brand new drywall.
It’s undoubtedly not what I had deliberate. I had hoped that I’d be putting in the brand new mural as we speak, however clearly, that must be pushed again a few days whereas this will get completed. It’s not simply the lengthy wall that must be redone. I’ll need to repeat this course of on the opposite cupboard wall within the “workplace” nook of the room, the place I’ll have to chop out this part of drywall…
So a few of you might be in all probability questioning how I’m going to plug issues in simply if I’m shifting all the retailers down, behind the decrease cupboards, as a substitute of up above the countertop. I’m going to make the retailers simply accessible and usable by buying a number of of those countertop grommet retailers. (That’s an affiliate hyperlink.)
These countertop grommet retailers are put in proper within the countertop. I’ll drill a 3-inch gap within the countertop wherever I would like retailers, after which the grommet outlet screws into the countertop and the wire beneath the desktop will plug into the newly-placed outlet. So these countertop grommet retailers will give me handy entry to retailers to be used at desktop degree whereas eliminating the necessity for retailers on the wall above the countertop. I feel it’ll work completely!
It appears like a couple of steps backwards, but it surely was crucial. And even with this setback and extra electrical and drywall work needing to be executed, it’s nonetheless an entire lot simpler and fewer time-consuming that constructing cupboards from scratch! So it’ll nonetheless be a internet constructive when all is claimed and executed.
Addicted 2 Adorning is the place I share my DIY and adorning journey as I transform and beautify the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do the vast majority of the work on the home on my own. You’ll be able to be taught extra about me right here.
[ad_2]
Source link